worktop radius

Hello There, Guest! Register

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Thread Modes

worktop radius

kitkat Offline

Offline

Time Served Poster

Posts: 709
Threads: 63
Likes Received: 0 in 0 posts
Likes Given: 0
Joined: Jan 2008
Reputation: 0
Tokens: 2,139

#2

03-06-2009, 08:07 PM

i always use a shelf or part of the unit going under neath ? same set up on my router as for mason mitres /9 mm offset , also do it for laminate tops , but i belt sand the back of the edging to reduce that thick line you otherwise get and push the curve forward so it dos nt taper as much coming out of the bull nose .

Find

Reply

« Next Oldest | Next Newest »

Messages In This Thread

worktop radius - by jaysparx - 03-06-2009, 07:56 PM

RE: worktop radius - by kitkat - 03-06-2009, 08:07 PM

RE: worktop radius - by jonny round boy - 03-06-2009, 10:40 PM

RE: worktop radius - by jonny round boy - 03-06-2009, 11:09 PM

RE: worktop radius - by PJK - 26-02-2011, 01:02 AM

RE: worktop radius - by Caly - 01-03-2011, 01:03 AM

RE: worktop radius - by Stretch - 03-06-2009, 11:14 PM

RE: worktop radius - by jonny round boy - 03-06-2009, 11:16 PM

RE: worktop radius - by chip off the block - 03-06-2009, 11:41 PM

RE: worktop radius - by jaysparx - 04-06-2009, 05:32 PM

RE: worktop radius - by marc1106 - 05-06-2009, 07:44 AM

RE: worktop radius - by M Howe Joinery - 05-06-2009, 05:07 PM

RE: worktop radius - by Dales and Moor - 05-06-2009, 07:10 PM

RE: worktop radius - by donaldmac - 22-02-2011, 12:16 PM

RE: worktop radius - by jonny round boy - 22-02-2011, 12:40 PM

RE: worktop radius - by Guest - 22-02-2011, 01:07 PM

RE: worktop radius - by jonny round boy - 22-02-2011, 01:48 PM

RE: worktop radius - by Guest - 22-02-2011, 02:01 PM

RE: worktop radius - by Guest - 22-02-2011, 02:07 PM

RE: worktop radius - by jonny round boy - 22-02-2011, 03:42 PM

RE: worktop radius - by jonny round boy - 22-02-2011, 03:51 PM

RE: worktop radius - by Guest - 22-02-2011, 04:02 PM

RE: worktop radius - by jonny round boy - 22-02-2011, 07:10 PM

RE: worktop radius - by jonny round boy - 22-02-2011, 07:27 PM

RE: worktop radius - by Stretch - 22-02-2011, 08:13 PM

RE: worktop radius - by Guest - 22-02-2011, 10:49 PM

RE: worktop radius - by jonny round boy - 22-02-2011, 11:10 PM

RE: worktop radius - by jonny round boy - 26-02-2011, 01:39 PM

RE: worktop radius - by PJK - 28-02-2011, 12:34 AM

RE: worktop radius - by rotax81 - 28-02-2011, 10:45 PM

RE: worktop radius - by jonny round boy - 01-03-2011, 12:28 PM

RE: worktop radius - by Caly - 01-03-2011, 09:48 PM

RE: worktop radius - by Alritegeezer - 21-01-2014, 08:42 PM

RE: worktop radius - by doonjwaft - 13-10-2018, 04:55 PM

RE: worktop radius - by jonny round boy - 13-10-2018, 05:50 PM

RE: worktop radius - by doonjwaft - 13-10-2018, 06:20 PM

RE: worktop radius - by jonny round boy - 13-10-2018, 06:49 PM

RE: worktop radius - by PJK - 14-10-2018, 04:12 AM

RE: worktop radius - by doonjwaft - 14-10-2018, 07:01 PM

RE: worktop radius - by snezza - 14-10-2018, 07:29 PM

RE: worktop radius - by doonjwaft - 14-10-2018, 08:14 PM

RE: worktop radius - by snezza - 14-10-2018, 08:35 PM

RE: worktop radius - by doonjwaft - 14-10-2018, 08:46 PM

RE: worktop radius - by snezza - 14-10-2018, 08:57 PM

RE: worktop radius - by doonjwaft - 14-10-2018, 09:10 PM

RE: worktop radius - by snezza - 14-10-2018, 09:30 PM

RE: worktop radius - by doonjwaft - 14-10-2018, 09:40 PM

RE: worktop radius - by snezza - 14-10-2018, 09:42 PM

RE: worktop radius - by doonjwaft - 14-10-2018, 10:05 PM

RE: worktop radius - by snezza - 14-10-2018, 10:27 PM

RE: worktop radius - by doonjwaft - 14-10-2018, 10:30 PM

RE: worktop radius - by PJK - 15-10-2018, 06:53 PM

RE: worktop radius - by doonjwaft - 15-10-2018, 08:13 PM

RE: worktop radius - by snezza - 16-10-2018, 07:46 AM

RE: worktop radius - by doonjwaft - 30-07-2020, 09:50 PM

Users browsing this thread: 2 Guest(s)