worktop radius

Hello There, Guest! Register

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Thread Modes

worktop radius

Guest
Guest

Tokens: 0

#24

22-02-2011, 10:49 PM

Brilliant, Thank you so much for your help. That is exactly as I want it. What size stainless stud would you use and what resin?

I am assuming that I do all the cutting and glueing before I touch the surface with oil, but I will still need to oil both sides before final fit.

Worktops arrived today so I'll start on the above tomorrow.

Again, many thanks for all your help. Donald

Reply

« Next Oldest | Next Newest »

Messages In This Thread

worktop radius - by jaysparx - 03-06-2009, 07:56 PM

RE: worktop radius - by kitkat - 03-06-2009, 08:07 PM

RE: worktop radius - by jonny round boy - 03-06-2009, 10:40 PM

RE: worktop radius - by jonny round boy - 03-06-2009, 11:09 PM

RE: worktop radius - by PJK - 26-02-2011, 01:02 AM

RE: worktop radius - by Caly - 01-03-2011, 01:03 AM

RE: worktop radius - by Stretch - 03-06-2009, 11:14 PM

RE: worktop radius - by jonny round boy - 03-06-2009, 11:16 PM

RE: worktop radius - by chip off the block - 03-06-2009, 11:41 PM

RE: worktop radius - by jaysparx - 04-06-2009, 05:32 PM

RE: worktop radius - by marc1106 - 05-06-2009, 07:44 AM

RE: worktop radius - by M Howe Joinery - 05-06-2009, 05:07 PM

RE: worktop radius - by Dales and Moor - 05-06-2009, 07:10 PM

RE: worktop radius - by donaldmac - 22-02-2011, 12:16 PM

RE: worktop radius - by jonny round boy - 22-02-2011, 12:40 PM

RE: worktop radius - by Guest - 22-02-2011, 01:07 PM

RE: worktop radius - by jonny round boy - 22-02-2011, 01:48 PM

RE: worktop radius - by Guest - 22-02-2011, 02:01 PM

RE: worktop radius - by Guest - 22-02-2011, 02:07 PM

RE: worktop radius - by jonny round boy - 22-02-2011, 03:42 PM

RE: worktop radius - by jonny round boy - 22-02-2011, 03:51 PM

RE: worktop radius - by Guest - 22-02-2011, 04:02 PM

RE: worktop radius - by jonny round boy - 22-02-2011, 07:10 PM

RE: worktop radius - by jonny round boy - 22-02-2011, 07:27 PM

RE: worktop radius - by Stretch - 22-02-2011, 08:13 PM

RE: worktop radius - by Guest - 22-02-2011, 10:49 PM

RE: worktop radius - by jonny round boy - 22-02-2011, 11:10 PM

RE: worktop radius - by jonny round boy - 26-02-2011, 01:39 PM

RE: worktop radius - by PJK - 28-02-2011, 12:34 AM

RE: worktop radius - by rotax81 - 28-02-2011, 10:45 PM

RE: worktop radius - by jonny round boy - 01-03-2011, 12:28 PM

RE: worktop radius - by Caly - 01-03-2011, 09:48 PM

RE: worktop radius - by Alritegeezer - 21-01-2014, 08:42 PM

RE: worktop radius - by doonjwaft - 13-10-2018, 04:55 PM

RE: worktop radius - by jonny round boy - 13-10-2018, 05:50 PM

RE: worktop radius - by doonjwaft - 13-10-2018, 06:20 PM

RE: worktop radius - by jonny round boy - 13-10-2018, 06:49 PM

RE: worktop radius - by PJK - 14-10-2018, 04:12 AM

RE: worktop radius - by doonjwaft - 14-10-2018, 07:01 PM

RE: worktop radius - by snezza - 14-10-2018, 07:29 PM

RE: worktop radius - by doonjwaft - 14-10-2018, 08:14 PM

RE: worktop radius - by snezza - 14-10-2018, 08:35 PM

RE: worktop radius - by doonjwaft - 14-10-2018, 08:46 PM

RE: worktop radius - by snezza - 14-10-2018, 08:57 PM

RE: worktop radius - by doonjwaft - 14-10-2018, 09:10 PM

RE: worktop radius - by snezza - 14-10-2018, 09:30 PM

RE: worktop radius - by doonjwaft - 14-10-2018, 09:40 PM

RE: worktop radius - by snezza - 14-10-2018, 09:42 PM

RE: worktop radius - by doonjwaft - 14-10-2018, 10:05 PM

RE: worktop radius - by snezza - 14-10-2018, 10:27 PM

RE: worktop radius - by doonjwaft - 14-10-2018, 10:30 PM

RE: worktop radius - by PJK - 15-10-2018, 06:53 PM

RE: worktop radius - by doonjwaft - 15-10-2018, 08:13 PM

RE: worktop radius - by snezza - 16-10-2018, 07:46 AM

RE: worktop radius - by doonjwaft - 30-07-2020, 09:50 PM

Users browsing this thread: 3 Guest(s)